Mcmillan Rod and Custom

External Moldings / Vents / Accents

Please call us @ 715-387-6847 to place an order.

We have two different types of moldings available. They are half round and low profile moldings. Both are solid, polished stainless steel, sold by the linear foot and have a multitude of possibilities.  Whatever is used for the half round moldings, can also be made from our low profile moldings (even running board strips).

More information is available on the Low Profile Moldings page, Running Board Strips page and Interior Moldings page.

HALF ROUND MOLDINGS

The half round moldings are machined from solid, type 304 stainless steel and polished to a mirror finish.

MOLDINGS AVAILABLE:
3/4" is $25/foot
5/8" is $23/foot
1/2" is $18-$21/foot (See to the right.)
3/8" is $24/foot
1/4" is $23/foot

1/2" is sold by total linear footage of order and is as follows:
Up to 3 feet is sold at $21/foot.
3-10 feet is $20/foot.
10-20 feet is $19/foot.
Over 20 feet is $18/foot.
Call for quote

The four pictures below are examples of end configurations for the moldings. Diagonal is also available. Mounting studs are recommended for door panels and applications outside of your ride.

The studs are $5 each and one is pictured below.

STUDS

This is an example of a 8-32 stud on 1/2" moldings. The 6-32 studs are used for the 1/4" moldings. Studs are $5 each.

BALL MILLED MOLDINGS
These moldings are 1/2" wide, solid half round and ball milled in your choice of 1/8", 3/16", and 1/4" widths. CALL 715-387-6847 FOR A PRICE QUOTE.
Machined from solid type 304 Stainless Steel and can be used for interior/exterior moldings and accents.
Options for end configurations include the same as the half round.

LOW PROFILE MOLDINGS
CHECK out the "Low Profile Moldings" page for more information.
Low profile moldings offer a lower height profile than the standard half round moldings.
The cost is by the linear foot:
3/4" (3/16" thick) = $25/foot
1" (1/4" thick) = $30/foot
1 1/4" (1/4" thick) = $35/foot

1/2" Low Profile Moldings
The cost is by the linear foot:
1/2" (5/32" thick) = $20/foot
More information found on the "Low Profile Moldings" page.

EXAMPLES OF MOLDINGS - more on the bottom of the page

Kenny_DicksideMoldings

35ChevTrimDeWitt

HOOD VENTS/BODY ACCENTS
New stylish, functional hood side vents. Precision built in the USA from type 304 stainless steel and polished to a mirror like finish using our 3/8" half round trim. They are available in single, double, and triple units. They can also be used in applications where a little style and flash is desired such as: interior/door panel trim and motorcycle saddlebag accents. Sold in pairs with hardware included, easy bolt in installation after your vehicle is painted.


Price for triple is $249/pair, double is $149/pair and single is $99/pair.

Picture of the three types of vents.

Triple vents

Double vents

Vents33Ford

Vents

Four single vents

37FordRoadster

37 Ford Roadster

Ventscropped

Double vents

VentsToronto

Toronto with vents

SADDLE BAG TRIM & ACCENTS
The lid trim is built from 1/2" solid stainless steel molding stock, polished to a mirror like finish and comes complete with studs installed. The side accents are actually our popular hood side vent assemblies. Also made from high quality stainless steel, they add a little flash to your bags. $189 plus S&H.

These are moldings for the motorcycle "Hardpack" saddlebag covers made from our 1/2" half round moldings. On the left, they are shown on a Harley.

© 2018 Mcmillan Rod and Custom